 |
HyPerformance plasma source Hypertherm HPR 130 |
|
plasma power source
The Hypertherm HyPerformance Plasma mechanized systems deliver incomparable HyDefinition cut quality at half the operating costs. By incorporating Hypertherm’s proven HyDefinition and LongLife technologies, HyPerformance Plasma boosts overall performance, productivity and profitability. The systems offer unmatched process flexibility to cut, bevel and mark metals up to 64 mm (2-1/2") thick.
Available are the HPR 130 with 130 A and the HPR 160 with 160 A amperage. |
|
|
HPR130 |
HPR260 |
capacity |
mild steel |
dross free |
16 mm
(5/8") |
32 mm
(1-1/4") |
production (pierce) |
25 mm
(1") |
32 mm
(1-1/4") |
severance (e dge starts) |
38 mm
(1-1/2") |
64 mm
(2-1/2") |
stainless steel |
production (pierce) |
20 mm (3/4") |
32 mm
(1-1/4") |
severance (edge starts) |
25 mm
(1") |
50 mm
(2") |
Aluminum |
production (pierce) |
20 mm
(3/4") |
25 mm
(1") |
severance (edge starts) |
25 mm
(1") |
50 mm
(2") |
speed* |
mild steel |
optimum quality |
12 mm
(1/2") |
12 mm
(1/2") |
2200 mm/m
(80 ipm) |
3850 mm/m
(145 ipm) |
cut angle |
ISO 9013 range* * |
2-4° |
2-4° |
weldability |
ready to weld |
process gases by material |
(Plasma/shield) |
mild steel |
O2/Air, O2/O2 |
stainless steel |
H35/N2, N2/N2
H35-N2/N2, F5/N2 |
Aluminum |
H35/N2, Air/Air
H35-N2/N2 |
process amps |
not all processes are available for all materials |
30-130 |
30-260 |
|
|
| * Note: Take care in comparison: competitors often show maximum cutting speeds rather than speeds that deliver the best cuts, as shown above. Cut speeds listed above deliver best cut quality, but cut speeds can be up to 50% faster. |
|
| ** ISO 9013 is a standard that defines cut quality of thermally cut parts. The lower the range (range 1 is the lowest), the smaller the angle on the cut face. Cut angle in range 4 is better than in range 5. |
|
standard equipment
• HyPerformance plasma power source
Hypertherm
• automatic gas consol Hypertherm
• plasma ignition consol Hypertherm
• command torch height control by plasma
arc voltage Hypertherm
• CNC Siemens Sinumerik 840 DI
• movable operator pendant panel
• Software HYPERNEST for manual and
automatic nesting
• marking system
• control of filter unit by CNC
• remote control diagnostic by Ethernet
• spare parts starting kit
• cutting plate alignment function
• max. cutting speed 12 m/min.
• positioning speed 35 m/min.
• cutting accuracy +/-0.1 mm
• positioning accuracy +/-0.05 mm
• repeat accuracy +/- 0.05 mm
• cutting table, independent from movement
mechanism, designed for heavy duty works with
special suction system
• machine and equipment according
to CE-regulations
|
|
optional equipment
• plasma torch brake away system
• filter unit
• additional plasma torch
• HPR 130 / HPR 260 plasma power source for
add. plasma torch
• MAX 200 plasma power source for
stainless steel
• additional oxy-fuel Torch
• marking system Hypertherm Arcwriter
• preparation for additional torch and length
adaptation (max. 4 m)
• manual torch tilting system
• feed rate
• operator pendant for torch height
control system (THC)
• software Pronest
• safety light barrier
• fault and program end signal lamp
• cutting plate alignment function (laser pointer)
• remote control option on large tables
• drawing of the cutting table
|
